| PIC18F14K22LIN | ||||
|---|---|---|---|---|
| CONFIG1H (address:0x300001, mask:0xFF, default:0x27) | ||||
| FOSC -- Oscillator Selection bits (bitmask:0x0F) | ||||
| FOSC = LP | 0xF0 | LP oscillator. | ||
| FOSC = XT | 0xF1 | XT oscillator. | ||
| FOSC = HS | 0xF2 | HS oscillator. | ||
| FOSC = ERCCLKOUT | 0xF3 | External RC oscillator, CLKOUT function on OSC2. | ||
| FOSC = ECCLKOUTH | 0xF4 | EC, CLKOUT function on OSC2 (high). | ||
| FOSC = ECH | 0xF5 | EC (high). | ||
| FOSC = ERC | 0xF7 | External RC oscillator. | ||
| FOSC = IRC | 0xF8 | Internal RC oscillator. | ||
| FOSC = IRCCLKOUT | 0xF9 | Internal RC oscillator, CLKOUT function on OSC2. | ||
| FOSC = ECCLKOUTM | 0xFA | EC, CLKOUT function on OSC2 (medium). | ||
| FOSC = ECM | 0xFB | EC (medium). | ||
| FOSC = ECCLKOUTL | 0xFC | EC, CLKOUT function on OSC2 (low). | ||
| FOSC = ECL | 0xFD | EC (low). | ||
| PLLEN -- 4 X PLL Enable bit (bitmask:0x10) | ||||
| PLLEN = OFF | 0xEF | PLL is under software control. | ||
| PLLEN = ON | 0xFF | Oscillator multiplied by 4. | ||
| PCLKEN -- Primary Clock Enable bit (bitmask:0x20) | ||||
| PCLKEN = OFF | 0xDF | Primary clock is under software control. | ||
| PCLKEN = ON | 0xFF | Primary clock enabled. | ||
| FCMEN -- Fail-Safe Clock Monitor Enable (bitmask:0x40) | ||||
| FCMEN = OFF | 0xBF | Fail-Safe Clock Monitor disabled. | ||
| FCMEN = ON | 0xFF | Fail-Safe Clock Monitor enabled. | ||
| IESO -- Internal/External Oscillator Switchover bit (bitmask:0x80) | ||||
| IESO = OFF | 0x7F | Oscillator Switchover mode disabled. | ||
| IESO = ON | 0xFF | Oscillator Switchover mode enabled. | ||
| CONFIG2L (address:0x300002, mask:0x1F, default:0x1F) | ||||
| PWRTEN -- Power-up Timer Enable bit (bitmask:0x01) | ||||
| PWRTEN = ON | 0xFE | PWRT enabled. | ||
| PWRTEN = OFF | 0xFF | PWRT disabled. | ||
| BOREN -- Brown-out Reset Enable bits (bitmask:0x06) | ||||
| BOREN = OFF | 0xF9 | Brown-out Reset disabled in hardware and software. | ||
| BOREN = ON | 0xFB | Brown-out Reset enabled and controlled by software (SBOREN is enabled). | ||
| BOREN = NOSLP | 0xFD | Brown-out Reset enabled in hardware only and disabled in Sleep mode (SBOREN is disabled). | ||
| BOREN = SBORDIS | 0xFF | Brown-out Reset enabled in hardware only (SBOREN is disabled). | ||
| BORV -- Brown Out Reset Voltage bits (bitmask:0x18) | ||||
| BORV = 30 | 0xE7 | VBOR set to 3.0 V nominal. | ||
| BORV = 27 | 0xEF | VBOR set to 2.7 V nominal. | ||
| BORV = 22 | 0xF7 | VBOR set to 2.2 V nominal. | ||
| BORV = 19 | 0xFF | VBOR set to 1.9 V nominal. | ||
| CONFIG2H (address:0x300003, mask:0x1F, default:0x1F) | ||||
| WDTEN -- Watchdog Timer Enable bit (bitmask:0x01) | ||||
| WDTEN = OFF | 0xFE | WDT is controlled by SWDTEN bit of the WDTCON register. | ||
| WDTEN = ON | 0xFF | WDT is always enabled. SWDTEN bit has no effect. | ||
| WDTPS -- Watchdog Timer Postscale Select bits (bitmask:0x1E) | ||||
| WDTPS = 1 | 0xE1 | 1:1. | ||
| WDTPS = 2 | 0xE3 | 1:2. | ||
| WDTPS = 4 | 0xE5 | 1:4. | ||
| WDTPS = 8 | 0xE7 | 1:8. | ||
| WDTPS = 16 | 0xE9 | 1:16. | ||
| WDTPS = 32 | 0xEB | 1:32. | ||
| WDTPS = 64 | 0xED | 1:64. | ||
| WDTPS = 128 | 0xEF | 1:128. | ||
| WDTPS = 256 | 0xF1 | 1:256. | ||
| WDTPS = 512 | 0xF3 | 1:512. | ||
| WDTPS = 1024 | 0xF5 | 1:1024. | ||
| WDTPS = 2048 | 0xF7 | 1:2048. | ||
| WDTPS = 4096 | 0xF9 | 1:4096. | ||
| WDTPS = 8192 | 0xFB | 1:8192. | ||
| WDTPS = 16384 | 0xFD | 1:16384. | ||
| WDTPS = 32768 | 0xFF | 1:32768. | ||
| CONFIG3H (address:0x300005, mask:0x88, default:0x88) | ||||
| HFOFST -- HFINTOSC Fast Start-up bit (bitmask:0x08) | ||||
| HFOFST = OFF | 0xF7 | The system clock is held off until the HFINTOSC is stable. | ||
| HFOFST = ON | 0xFF | HFINTOSC starts clocking the CPU without waiting for the oscillator to stablize. | ||
| MCLRE -- MCLR Pin Enable bit (bitmask:0x80) | ||||
| MCLRE = OFF | 0x7F | RA3 input pin enabled; MCLR disabled. | ||
| MCLRE = ON | 0xFF | MCLR pin enabled, RA3 input pin disabled. | ||
| CONFIG4L (address:0x300006, mask:0xCD, default:0x85) | ||||
| STVREN -- Stack Full/Underflow Reset Enable bit (bitmask:0x01) | ||||
| STVREN = OFF | 0xFE | Stack full/underflow will not cause Reset. | ||
| STVREN = ON | 0xFF | Stack full/underflow will cause Reset. | ||
| LVP -- Single-Supply ICSP Enable bit (bitmask:0x04) | ||||
| LVP = OFF | 0xFB | Single-Supply ICSP disabled. | ||
| LVP = ON | 0xFF | Single-Supply ICSP enabled. | ||
| BBSIZ -- Boot Block Size Select bit (bitmask:0x08) | ||||
| BBSIZ = OFF | 0xF7 | 1kW boot block size. | ||
| BBSIZ = ON | 0xFF | 2kW boot block size. | ||
| XINST -- Extended Instruction Set Enable bit (bitmask:0x40) | ||||
| XINST = OFF | 0xBF | Instruction set extension and Indexed Addressing mode disabled (Legacy mode). | ||
| XINST = ON | 0xFF | Instruction set extension and Indexed Addressing mode enabled. | ||
| DEBUG -- Background Debugger Enable bit (bitmask:0x80) | ||||
| DEBUG = ON | 0x7F | Background debugger enabled, RA0 and RA1 are dedicated to In-Circuit Debug. | ||
| DEBUG = OFF | 0xFF | Background debugger disabled, RA0 and RA1 configured as general purpose I/O pins. | ||
| CONFIG5L (address:0x300008, mask:0x03, default:0x03) | ||||
| CP0 -- Code Protection bit (bitmask:0x01) | ||||
| CP0 = ON | 0xFE | Block 0 code-protected. | ||
| CP0 = OFF | 0xFF | Block 0 not code-protected. | ||
| CP1 -- Code Protection bit (bitmask:0x02) | ||||
| CP1 = ON | 0xFD | Block 1 code-protected. | ||
| CP1 = OFF | 0xFF | Block 1 not code-protected. | ||
| CONFIG5H (address:0x300009, mask:0xC0, default:0xC0) | ||||
| CPB -- Boot Block Code Protection bit (bitmask:0x40) | ||||
| CPB = ON | 0xBF | Boot block code-protected. | ||
| CPB = OFF | 0xFF | Boot block not code-protected. | ||
| CPD -- Data EEPROM Code Protection bit (bitmask:0x80) | ||||
| CPD = ON | 0x7F | Data EEPROM code-protected. | ||
| CPD = OFF | 0xFF | Data EEPROM not code-protected. | ||
| CONFIG6L (address:0x30000A, mask:0x03, default:0x03) | ||||
| WRT0 -- Write Protection bit (bitmask:0x01) | ||||
| WRT0 = ON | 0xFE | Block 0 write-protected. | ||
| WRT0 = OFF | 0xFF | Block 0 not write-protected. | ||
| WRT1 -- Write Protection bit (bitmask:0x02) | ||||
| WRT1 = ON | 0xFD | Block 1 write-protected. | ||
| WRT1 = OFF | 0xFF | Block 1 not write-protected. | ||
| CONFIG6H (address:0x30000B, mask:0xE0, default:0xE0) | ||||
| WRTC -- Configuration Register Write Protection bit (bitmask:0x20) | ||||
| WRTC = ON | 0xDF | Configuration registers write-protected. | ||
| WRTC = OFF | 0xFF | Configuration registers not write-protected. | ||
| WRTB -- Boot Block Write Protection bit (bitmask:0x40) | ||||
| WRTB = ON | 0xBF | Boot block write-protected. | ||
| WRTB = OFF | 0xFF | Boot block not write-protected. | ||
| WRTD -- Data EEPROM Write Protection bit (bitmask:0x80) | ||||
| WRTD = ON | 0x7F | Data EEPROM write-protected. | ||
| WRTD = OFF | 0xFF | Data EEPROM not write-protected. | ||
| CONFIG7L (address:0x30000C, mask:0x03, default:0x03) | ||||
| EBTR0 -- Table Read Protection bit (bitmask:0x01) | ||||
| EBTR0 = ON | 0xFE | Block 0 protected from table reads executed in other blocks. | ||
| EBTR0 = OFF | 0xFF | Block 0 not protected from table reads executed in other blocks. | ||
| EBTR1 -- Table Read Protection bit (bitmask:0x02) | ||||
| EBTR1 = ON | 0xFD | Block 1 protected from table reads executed in other blocks. | ||
| EBTR1 = OFF | 0xFF | Block 1 not protected from table reads executed in other blocks. | ||
| CONFIG7H (address:0x30000D, mask:0x40, default:0x40) | ||||
| EBTRB -- Boot Block Table Read Protection bit (bitmask:0x40) | ||||
| EBTRB = ON | 0xBF | Boot block protected from table reads executed in other blocks. | ||
| EBTRB = OFF | 0xFF | Boot block not protected from table reads executed in other blocks. | ||
This page generated automatically by the device-help.pl program (2016-08-21 09:07:41 UTC) from the 8bit_device.info file (rev: 1.31) of mpasmx and from the gputils source package (rev: svn Unversioned directory). The mpasmx is included in the MPLAB X.